TCCX150-G

Specification	Value
Magnification	1.500 (x)
Image circle diameter	11.0 (mm)
Max sensor size	2/3″
1/3″	3.20 x 2.40 (mm x mm)
1/2.5″	3.80 x 2.85 (mm x mm)
1/2″	4.27 x 3.20 (mm x mm)
1/1.8″	4.75 x 3.55 (mm x mm)
2/3″	5.67 x 4.73 (mm x mm)
Working distance	132.3 (mm)
Working f/N	16
Telecentricity typical (max)	< 0.04 (0.06) (deg)
Distortion typical (max)	< 0.05 (0.10) (%)
Depth of field	0.40 (mm)
Resolution	7 (μm)
Light color, peak wavelength	green, 525 nm
Spectral FWHM	40 (nm)
Supply voltage	12-24 (V)
Max power consumption	2.5 (W)
LED voltage	3.3 (4.0) (V)
LED current	350 (mA)
Max pulse current	2000 (mA)
Connector	M8
Cables	CB244P1500 included
Mount	C
Phase adjustment	Yes
Length	147.2 (mm)
Front diameter	37.7 (mm)
Mass	519 (g)
Operating temperature	0-40 (°C)
Storage temperature	0-50 (°C)
Operating relative humidity	20-85, non condensing (%)
Installation	Indoor use only
Risk group according to CEI EN 62471:2010	Risk group 1

Description

Working distance: distance between the front end of the mechanics and the object. Set this distance within ± 3% of the nominal value for maximum resolution and minimum distortion.
Working f-number (wf/N): the real f-number of a lens in operating conditions.
Maximum angle between chief rays and optical axis on the object side. Typical (average production) values and maximum (guaranteed) values are listed.
Percent deviation of the real image compared to an ideal, undistorted image. Typical (average production) values and maximum (guaranteed) values are listed.
At the limits of the depth of field, the image can still be used for measurements. For a very sharp image, however, only half of the depth of field should be applied. Pixel size used for calculation is 3.45 μm.
Object side, calculated with the Rayleigh criterion with λ= 520 nm
At max forward current. Tolerance is ± 0.06V on forward voltage measurements.
Used in continuous (non-pulsed) mode.
At pulse width <= 10 ms, duty cycle <= 10% condition. Built-in electronics board must be bypassed (see tech info).
Measured from the front end of the mechanics to the camera flange.

Lens mount	C
Connector	M8
Accessory developer	Opto
Cables	CB244P1500 included
Zoom ratio	1.500 (x)
Working distance	132.3 (mm)
Working f/N	16
Telecentricity typical (max)	< 0.04 (0.06) (deg)
Distortion typical (max)	< 0.05 (0.10) (%)
Depth of field	0.40 (mm)
Phase adjustment	Yes
Mass	519 (g)
Image circle diameter	11.0 (mm)
Length	147.2 (mm)
Resolution	7 (μm)
Front diameter	37.7 (mm)
Supply voltage	12-24 (V)
Operating temperature	0-40 (°C)
Storage temperature	0-50 (°C)
Installation	Indoor use only
Light color, peak wavelength	green, 525 nm
Max power consumption	2.5 (W)
Led voltage	3.3 (4.0) (V)
Led current	350 (mA)
Max pulse current	2000 (mA)
Operating relative humidity	20-85, non condensing (%)
Risk group (cei 62471)	Risk group 1
Spectral fwhm	40 (nm)
Optmag	1.500 (x)
Sensor size